MoparFins

Please login or register.

Login with username, password and session length
Advanced search  

News:

We changed servers, which is good, and lost all passwords, which is bad. See above.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - mike

Pages: 1 [2] 3 4
16
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: April 02, 2012, 04:59:00 AM »


And im going to try and get up there this week to check with him and look at the cars.

17
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: April 01, 2012, 06:10:12 PM »


yea rock auto parts list the front 2 as the same ones and has the rear>plus has the one from the master cyl to the T block but it list different ones for auto and std trans cars.

18
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: April 01, 2012, 12:11:42 PM »


ok and no theres a rubber from the master cylinder.

19
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: April 01, 2012, 08:11:07 AM »


i planned in that  i found them on rock auto so the 2 front will interchange with each other?  And i was going to order the one from the master cyl to dist block but thay dont have it in stock.

20
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: April 01, 2012, 07:50:22 AM »


Well i found the only line i have to replace is the one going to the rear and thats all pretty stright the fuel line isnt rusted and so ill see if i can re use that seeing its all ready on the car. Thr front lines are good and are not rusted or leaking. so i think brake line wont be to bad for me to do.

21
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: March 31, 2012, 04:29:25 PM »


Updates soon

22
Tech- - FUEL / Rebuilt Carb No Start
« on: March 21, 2012, 07:48:38 PM »


na thats ok lol and  though now i think of it the tape will be easier lol

23
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: March 21, 2012, 07:17:14 PM »


Well got all the rubber undercoating stripped away today going in the am to see about  haveing  the tank  boiled.  Got the sending unit apart and actually working :D :D  just got to find something that will clean the copper up  its full of green  corrosion but need something that doesnt harm the rubber on it. Any hints lol and the molasses ive seen that on youtube lol.

24
Tech- - FUEL / Rebuilt Carb No Start
« on: March 21, 2012, 07:10:46 PM »


And  Firedome / Roger yea deff id like to show her just let me know lol

25
Tech- - FUEL / Rebuilt Carb No Start
« on: March 21, 2012, 03:50:09 PM »


i love wiring actually one of the things i enjoy. And yes if you could i wanted to do that from the start go. Thanks

26
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: March 21, 2012, 02:33:04 PM »


i got a place that can boil it. i just dont kanow about the inline fuel filter made in the tank and also the sending unit in it is rough and i only found 2 online one for $189 and another NOS $258 =O crazy price

27
Tech- - FUEL / Rebuilt Carb No Start
« on: March 21, 2012, 04:53:51 AM »


yes im deff going to fix the wiring one of the first things i noticed about the car lol

28
MEMBERS Project Cars in Progress / 56 Plymouth Belvedere Project
« on: March 20, 2012, 07:23:06 PM »


 

29
Tech- - FUEL / Rebuilt Carb No Start
« on: March 20, 2012, 05:55:30 PM »


 UPDATE:   Car is running like a kitten! i put the new spark plugs (really nasdty) Put new points in/new conectors to the coil/resistor. Pulled the carb off and  reset float and found out my aux pump in the carb wasnt set right. Changed the oil/filter new fuel filter and she's running really good. Just need to adj the idle and fine tune carb a little. Also did a compression test and got around 140-150 :D

30
Tech- - FUEL / Rebuilt Carb No Start
« on: March 17, 2012, 06:39:33 PM »


the pump works great i checked it and its been replaced once allready

Pages: 1 [2] 3 4
© 2008-2014 Steve Hobby • © 2015 Allpar, LLC