MoparFins

Please login or register.

Login with username, password and session length
Advanced search  

News:

We changed servers, which is good, and lost all passwords, which is bad. See above.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Brian

Pages: 1 2 3 [4] 5 6 ... 147
46
Turns out I nicked the inner seal on the threads when installing it.  Gouged the seal and popped the spring loose as well.



And with all that oil everywhere the rear shoes were toast!



So off to the parts store for some new Wagner riveted 12x3 shoes, and SKF inner seals....Did not want to use the raybestos bonded units. ;)







47
Well i redid the rear brake hubs a few weeks ago, new bearings and seals, but yesterday on my first day off in about a week I noticed that there was gear oil on the ground by the passenger side rear tire....Doooh!

So today I tore into it to see how bad it was....





All that oil everywhere...that can't be good.





48
MEMBERS Project Cars in Progress / The Sheriff
« on: February 09, 2015, 06:26:32 PM »
Quote from: czervika

 And I'm, behind on the winters project of getting the trans rebuilt.  To be honest I'm waiting on my bonus to be able to afford the rebuild kit. 


Aren't we all.....  I still need to totally re-wire the Desoto....


49
Tech- - Engine / ArchOil Not Snake Oil
« on: February 09, 2015, 06:24:05 PM »
I've sat up and taken notice as well...I'd like to know too!


50
Quote from: POLARACO
Good thing you're not an Ice Road trucker.  LOL

If it was a company truck then I wouldn't care so much....



51
General BS and Laughs / It's 2015..
« on: February 09, 2015, 06:17:59 PM »
Quote from: POLARACO
Quote from: thrashingcows
Beautiful day here today.  Got up to about 15*C (60+*F)...cloudy with a bit of sun from time to time.  Heck the trees and shrubs are starting to bud and bloom already!


Heheheheh.....


52
MEMBERS Project Cars in Progress / The Sheriff
« on: February 08, 2015, 06:59:06 PM »
Wow....Nice job!


53
General Tech / Serpentine belt retro
« on: February 08, 2015, 06:54:09 PM »
I have to agree with Snotty on this one as well.  I am not a fan of the serpentine belts on the old mopar motors...or any old style V8 really.  Ad trying to make up a system from scratch!  That could be a huge job!

I would head over to Bouchillon performance and look at what they have.  Some of their stuff...including the Sanden AC compressor kits (which I used on the 440 in the wagon) are quite nice.


54
General BS and Laughs / It's 2015..
« on: February 08, 2015, 06:50:26 PM »
Beautiful day here today.  Got up to about 15*C (60+*F)...cloudy with a bit of sun from time to time.  Heck the trees and shrubs are starting to bud and bloom already!


55
Quote from: POLARACO
Someone said steering box.  I'm surprised you have so many loose bolts though.  Too many Burger Kings?  LOL  I thought i was the one who forgot shtuff

It was that brutally rough Ice Road trucking I did hauling my brother trucks up into the interior and back.  The roads were washboard for at least 200 miles!  Shook a lot of stuff loose on Ol' Patches.


56
Well today I decided to see where my "bang/Clunk" was coming from in the front end.  I was pretty sure it was the steering box, but had my neighbour crank the wheels back and forth while I watched and listened.  

Sure enough the box torqued in one direction, then when direction and torque was applied in the opposite direction I got a bang.  And you could see that the steering box had a lot of movement.

Pulled the battery, and IC tube on the DS and lifted up the splash guard.  Found one bolt half out and loose.  One other was just starting to loosen up.  So I removed the two I could remove, cleaned them up and blue loctited them in place.  The other two I backed out as for as I could, more blue loctite, and then tightened back up.

Cycled the steering again once everything was back together and all seems well. 


57
I measured from the ground to the top of the wheel well arch before I started, and after I was done, lost exactly 1.5" on each side.  And I can say the ride is like night and day!!  I used to cringe every time I ran over a manhole cover in the road....now it just absorbs the bump and you barely feel it.

I couldn't be happier with the ride so far.  Although I've only put a couple miles on it, but so far so good!

58
Transferred the two plates from the original pack to the new spring and installed.  Required a couple clamps to compress the spring so I could get the threads started on the center bolt.  Then it was just snug everything up and make sure all the plates and springs stayed in alignment.



Then once both side were done I had to lower the truck back down and get everything to line up.  Had to go back and forth taking a few inches out of each side to slowly lower it back down.  Once the weight was on the springs I installed the spring clamps.  Then finished re-installing everything.  Only had to cut about 3/4" to 1" off the U-bolts to make up for the difference in spring pack thickness.

All done and ready to go.





59
Did the spring prep last week in teh evenings.  So decided since I had a couple days off I would tackle the swap today.  Took about 5 hours from start to finish.

First was to get the sway bar end links off, and the shocks as well.  Then remove the U-bolts.  Once all the was off I could start to jack up the truck to give me enough clearance to loosen the retaining bolt in the center of the spring pack and remove the lower spring.



Ready to remove lower spring.



Here is a comparison of the second spring in this smooth ride set-up, and the new one that is going in.



Of the 3 wear tips on the lower springs only one was still in place and secure.  The others had broken loose.





60
Well I decided I would getting the front end to ride a bit smoother with the help of the thread below and user sevnt300 and his findings. Those "smooth ride" parabolic springs I installed during the 4wd conversion really did not smooth anything out in the ride....actually I think it made it stiffer. :(

Well Sevnt300 over in this thread...http://www.dieseltruckresource.com/forums/1st-gen-ram-all-topics-93/front-suspension-upgrade-301721/page10/ ....Post #138.  He has a cummins long box crew as well with these springs was not happy with the ride either.  He did a lot of R&D work to finally come up with a ride he was comfortable with.

So first I had to pull apart an old set of rear springs and find two leafs that would be 34" long and allow an even 17" on each side of the center hole.  Think it was the 3rd leaf up from the bottom.

One side already had a hole for the spring clamp and was 17", the other required about 3" to be cut off.  Then I had to tapper the tip.



I then went down to the shop that sold me the Smooth Ride springs...they are local....and picked up some new wear tips and spring clamps.



The rubbers that came with the new spring clamps would not work with their style, so i used some neoprene sheet I had to cut out some new ones that would.



Then I had to drill three 1/2" holes in each spring.  One for the wear tip, and two for the new spring clamps to lock into.  I positioned the spring clamps 6" back from the wear tips.



Tossed on some paint and got ready to do the swap.

Pages: 1 2 3 [4] 5 6 ... 147
© 2008-2014 Steve Hobby • © 2015 Allpar, LLC