MoparFins

Please login or register.

Login with username, password and session length
Advanced search  

News:

We changed servers, which is good, and lost all passwords, which is bad. See above.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Anthony Prescott

Pages: 1 2 [3] 4 5 ... 7
31
Tech- - DRIVE TRAIN / opinions welcome
« on: November 07, 2010, 06:40:02 PM »
t 18 is BW. its been sitting in the garage for a few years, 12xxx miles on it

32
Tech- - DRIVE TRAIN / opinions welcome
« on: November 07, 2010, 06:38:57 PM »
what about the t-18 out of a 67 jeep gladiator? i know they dont make an adaptor for it, but i have a friend who makes all kinds of castings. is it srtong enough??

33
Tech- - DRIVE TRAIN / opinions welcome
« on: November 07, 2010, 12:45:22 PM »
this is for a car though, right? unless they made a hemi tranny for a truck? never seen one, but i dont get out much. is there a hemi truck application with a granny gear?

34
Tech- - DRIVE TRAIN / opinions welcome
« on: November 06, 2010, 05:37:00 PM »
maybe the 4 speed used in the d-600 pickups? what are those?

35
Tech- - DRIVE TRAIN / opinions welcome
« on: November 06, 2010, 05:35:58 PM »
big block work truck... need a strong 4 or 5 speed manual. whats the strongest there is?  this is for  a canyon recovery truck. i want the reliability of the old ones from the 60´s and 70´s. anyway. whats the best one out there??? thanks.- a

36
Tech- - Engine / slant 6 head
« on: November 02, 2010, 10:34:19 PM »
ok... working on a 64 barracuda. slant 6... need a head with the spark plug sleeves in it. i think this is special for the 64 and 65. is there a good place to go, preferably in calif or oregon to find one?  is there a dodge junk yard in either state? anyone?

37
Tech- - DRIVE TRAIN / full screw rear ends?????????
« on: November 02, 2010, 12:53:48 PM »
tein screw means tandom rear axles, both of them powered by the engine.

38
Tech- - DRIVE TRAIN / full screw rear ends?????????
« on: November 02, 2010, 10:13:50 AM »
twin screw is right
. my buddy calls it a full screw.   but yeah.

39
General Tech / classic blue book????????
« on: November 01, 2010, 09:38:55 PM »
wow... i expected it to be worth more than 12k. maybe in a few years it´ll be higher. thanks.

40
Tech- - DRIVE TRAIN / full screw rear ends?????????
« on: November 01, 2010, 09:37:21 PM »
has anybody ever came accross a full screw set up for a 1 ton truck? saw one a lomg time ago, but cant remember who had it. can i make one? maybe it´ll be easier.

41
General Tech / classic blue book????????
« on: October 31, 2010, 07:13:02 PM »
where can i find a blue book price on a 53 chrysler? kbb only goes back to 1990

42
Tech- - Engine / 413 industrial
« on: October 29, 2010, 02:10:56 PM »
what is the purpose for the water line that runs from the water pump housing to the intake manifold?

43
Tech- - Engine / 331 hemi
« on: October 20, 2010, 11:06:37 PM »
can i put hardened valve seats in the 331 to avoid adding a lead addative? if so, where can i buy these? and should i get new valves with them?

44
General Tech / window rubber
« on: October 19, 2010, 11:17:31 AM »
ok ladies. thanks for the info. i´ll check out steele.

45
Tech- - Engine / ok. probably a stupid question....
« on: October 19, 2010, 11:14:12 AM »
good stuff. here´s why i ask... for those of you that have been following my rants, this question pretains to my 413 industrial. it was originally pulled from a 72 dodge commander motor home. the block is stamped for the 71 year. Obviously, it came with an automatic, but, as stares for the 71 motors, its drilled for the pilot bearing. Its got the original holley carb on it. i believe it to be a 650. i could be wrong. Vacuum advanced dist. yada yada. I know i can put a 4 speed behind it, but what would i have to do to the engine other than install the pilot bearing???¿¿¿

Pages: 1 2 [3] 4 5 ... 7
© 2008-2014 Steve Hobby • © 2015 Allpar, LLC