MoparFins

Please login or register.

Login with username, password and session length
Advanced search  

News:

We changed servers, which is good, and lost all passwords, which is bad. See above.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - Anthony Prescott

Pages: [1] 2
1
General Tech / i cant tell the difference
« on: November 26, 2010, 02:50:17 PM »
Whats the difference between a 1953 chrysler new yorker and same year new yorker deluxe??

2
General Tech / ¿¿¿What about oil???
« on: November 24, 2010, 11:37:22 AM »
I got to do an oil change in my 331 hemi. What is the best thing for the oldies? I also have to change the oil in a 67 dodge truck... the 413 industrial. Should I use the same in both?

3
General Tech / got a problem...
« on: November 19, 2010, 03:37:03 PM »
looking to swap a big block into a small block truck. what do i do about the cross over piece under the oil pan that attaches the frame together?? its a 2wd truck with independent front suspension. moparmanof852010-11-19 20:38:27

4
Tech- - Engine / SNOTTY!!!!!! 413 ind question
« on: November 15, 2010, 09:23:44 AM »
where do i rout the water line coming from the water pump to the intake manifold if i want to change the intake??? going with a fuel injection intake manifold and dont know if that water line is necessary for the cooling process. is it? hope not.

5
Tech- - DRIVE TRAIN / truck transfer case
« on: November 14, 2010, 06:27:07 PM »
i need a transfer case that i can shift without stopping... any thoughts?

6
Tech- - Engine / 413 industrial intake again
« on: November 14, 2010, 11:03:52 AM »
ok... the intake has a side mounted water line coming from the water pump. i want to change the intake to accomidate fuel injection. where do i rout this line to? i was told not to cap it off, so can i just run it into the heater hose???? thanks in advance. -a

7
General Tech / disk brakes???
« on: November 11, 2010, 12:07:39 PM »
where can i find a disk brake change over kit for my 53 chrysler?

8
General Tech / transmission cooler
« on: November 08, 2010, 10:11:42 AM »
how can i integrate a trans cooler into a manual trans?

9
Tech- - DRIVE TRAIN / opinions welcome
« on: November 06, 2010, 05:35:58 PM »
big block work truck... need a strong 4 or 5 speed manual. whats the strongest there is?  this is for  a canyon recovery truck. i want the reliability of the old ones from the 60´s and 70´s. anyway. whats the best one out there??? thanks.- a

10
Tech- - Engine / slant 6 head
« on: November 02, 2010, 10:34:19 PM »
ok... working on a 64 barracuda. slant 6... need a head with the spark plug sleeves in it. i think this is special for the 64 and 65. is there a good place to go, preferably in calif or oregon to find one?  is there a dodge junk yard in either state? anyone?

11
Tech- - DRIVE TRAIN / full screw rear ends?????????
« on: November 01, 2010, 09:37:21 PM »
has anybody ever came accross a full screw set up for a 1 ton truck? saw one a lomg time ago, but cant remember who had it. can i make one? maybe it´ll be easier.

12
General Tech / classic blue book????????
« on: October 31, 2010, 07:13:02 PM »
where can i find a blue book price on a 53 chrysler? kbb only goes back to 1990

13
Tech- - Engine / 413 industrial
« on: October 29, 2010, 02:10:56 PM »
what is the purpose for the water line that runs from the water pump housing to the intake manifold?

14
Tech- - Engine / ok. probably a stupid question....
« on: October 18, 2010, 09:47:59 AM »
i hear a lot of people say that an engine is made for acertain transmission  ex: ITS A 4 SPEED MOTOR.  what difference does it make? can you run an automatic behind a motor that came with a manual tranny? i dont see why not. info plase...

15
General Tech / window rubber
« on: October 17, 2010, 09:53:33 AM »
ok... in the process of replacing the rear window in my 53 chrysler new yorker. who sells the rubber strip for it? i need originsl style in order to reinstall the chrome molding over the top of it. thanks in advance.

Pages: [1] 2
© 2008-2014 Steve Hobby • © 2015 Allpar, LLC