MoparFins

Please login or register.

Login with username, password and session length
Advanced search  

News:

We changed servers, which is good, and lost all passwords, which is bad. See above.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Dave

Pages: [1]
1
General Tech- - BRAKES / Rebuilt caliper part installation
« on: January 28, 2010, 04:04:51 PM »
No Kidding, Stan.





2
General Tech- - BRAKES / Rebuilt caliper part installation
« on: January 28, 2010, 04:02:32 PM »
No, Scott, I was making a joke about the `anti-rattle- clip the kid is wearing on his face. No vibrations here. Thanks.




3
General Tech- - BRAKES / Rebuilt caliper part installation
« on: January 28, 2010, 04:40:53 AM »
Wheel balance problems - the kind that make your teeth rattle.

You know, so you... have to wear the....

Because your teeth, you know, they ...

(tap tap) Is this thing on???




4
WELCOME NEW MEMBERS! / Another new guy
« on: January 28, 2010, 04:36:18 AM »
So does that mean I can stay in the `He-Man-Woman-Hater's Club' ? I could duct tape a coupla cardboard fins on the rear quarters if it helps. :-)




5
General Tech- - BRAKES / Rebuilt caliper part installation
« on: January 27, 2010, 04:34:32 AM »
Is that the kind of anti-rattle clips you need when you've got bad wheel balance problems?




6
Tech- - Engine / I need help rebuilding this engine
« on: January 26, 2010, 08:45:44 PM »
Just reading the shop manual on that engine..." cylinder head bolts - use 256/16th wrench, torque to 120 mile-pounds... make sure to use LOTS of locktite..."




7
General Tech- - BRAKES / Rebuilt caliper part installation
« on: January 26, 2010, 03:46:49 PM »
Pictures!!! I can work with those. Awesome, thanks for all the replies, mucho appreciado


8
General Tech- - BRAKES / Rebuilt caliper part installation
« on: January 25, 2010, 06:51:58 PM »
Hi All,

I bought a pair of rebuilt Raybestos calipers for the Barracuda, and they came with a wire retainer/clip/something or other (pic included), and I can't figure out how it mounts on the caliper. There wasn't one of these on the old calipers. The hooks on the ends are the same width as the caliper bolts so I know `how' it mounts, and the long straight part must somehow go over the caliper body, placing it in any downward position causes it to interfere with pads or piston. Anybody got a clue that I don't?





9
General BS and Laughs / North Carolina Special
« on: January 25, 2010, 04:34:24 AM »
Do share,, if it's that bad it's probably in response to several emails questioning his sanity.


10
MEMBERS Project Cars in Progress / TC's T/C...update..Aug 2012
« on: January 24, 2010, 09:56:30 PM »
"Finish the bathroom first"... I have the same deal with our kitchen right now. Counters, backsplash, lighting, cieling, fireplace, paint.... Oil, grease, even brake fluid on my hands I can stand. Drywall dust - ick.




11
WELCOME NEW MEMBERS! / Another new guy
« on: January 24, 2010, 09:41:49 PM »
Thanks to you all. This is my first project, it's nowhere near numbers matching or original. This one is for fun and getting my feet wet. It's a '74, a previous owner jammed a 440 in place of the original 318, there's some yellow paint under the violet in places, even a red patch on the rad support. But lordy, it was fun to drive home!!! I'm making her roadworthy over the winter, brakes, fuel tank, etc. When the storage insurance runs out in May I will hopefully be ready to put it on the road in time for summer.  In the meantime, I have something to look forward to and to bash my knuckles on from time to time.














12
WELCOME NEW MEMBERS! / Another new guy
« on: January 21, 2010, 07:36:28 PM »
Hi all. I've been a member of mymopar.com for a while and this group seems like a good group as well. Thanks fer having me along.

Dave




Pages: [1]
© 2008-2014 Steve Hobby • © 2015 Allpar, LLC