MoparFins

Please login or register.

Login with username, password and session length
Advanced search  

News:

We changed servers, which is good, and lost all passwords, which is bad. See above.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - chuck lowe

Pages: [1] 2 3
1
WELCOME NEW MEMBERS! / new here
« on: March 26, 2012, 08:19:57 AM »


can - can is a dear old friend -----although no one would know it , the way we go back and forth at each other . like that fat boy that runs this place !-----------------------------------later

2
MEMBERS Project Cars in Progress / New Home/Old Dart
« on: March 19, 2012, 09:28:16 PM »




thanks guys . not quite sure about a console just yet . the way it's set up now kinda grew on me .  my dart has spent all it's life in WV. , charleston , to be exact . when i bought it it was painted red , thus it's name Big Red . it only has about 36k on her but has had some of the typical rust issues , like the front floors , which have been replaced . little rust around the quarter lips but real solid about everywhere else . i have the original dealer receipt a few other papers and believe it or not , the original key packet from delivery . when i started on her i had every intension of redoing her in red but steve will tell ya . i keep changin things around . what i wanted to do as you see it now was to do a modern day rat but not in all the rust and dent stages and keeping within the design of being engineered after the fighter jets of the late 50's , thus the molded tail lights and the wing . the wing i set on the trunk lid probably a dozen times before it was a go . the biggest effort was drilling mount holes , something i hope i never regret . as far as the hood pins go the hood , lets say , was really not in top condition , as it had earlier repairs . i'm hopin that within the next few months i'll have the 383-727 in with a custom slip drive shaft , rear discs brakes , with a hand brake . the rear is a 742 from a 67 ply. but with single 292 gears . it had a set of 391's but they were just a touch high . so i have a 741 sure grip that'll have 323's . i gotta set of knock off wires , with adapters but coming up with a grand for wide whites is going to be a stretch especially when i know i'll be rippin up the streets with em . i think thats the main reson the old trans is leakin so badly . i just can't keep my foot outta the gas and with the floor shifter , i shift every gear every time . i always said the reason god gave us gears was to shift em ! ------by the way , i'm goin on 63 and am still a gear head ,,,,,,,,,,,,but some may say bone head ----------------------------later60 dart2012-03-20 01:54:19

3
MEMBERS Project Cars in Progress / New Home/Old Dart
« on: March 19, 2012, 11:20:47 AM »





PSSSSSSSSS . if anyone wants to know , the sidepipes are functional and street legal !
60 dart2012-03-19 15:25:28

4
MEMBERS Project Cars in Progress / New Home/Old Dart
« on: March 19, 2012, 11:05:11 AM »



600 edelbrock for now . the trips are on the shelf . if the 383 goes in , i'm thinkin trip 2 g's . if i can get it to load , here's a photo of the floor shifter on my castiron torqueflite . i might just leave the fame on it and not bother with a matching look --------------------------later
60 dart2012-03-19 15:09:29

5
MEMBERS Project Cars in Progress / New Home/Old Dart
« on: March 19, 2012, 09:07:25 AM »



ya , i know theres doubles but i can't seem to remove em -----don't beat me up too bad------------------later
60 dart2012-03-19 13:09:00

6
MEMBERS Project Cars in Progress / New Home/Old Dart
« on: March 19, 2012, 08:28:42 AM »








my dart





POLARACO2012-03-22 21:01:23

7
WELCOME NEW MEMBERS! / new here
« on: March 18, 2012, 08:06:18 PM »
good lookin ride dragon . i think your best choices for engine upgrade would be a 383 0r 440 , with a 727 trans . reason being is that using the old castiron torqueflite is way to obsolete to find parts for and a trans from someone like tci can be had for about 12-1500 for a good street ripper trans . what i'm using is goin to be using a 64-383 , with stock 727 , at least for the moment . base advertised hp. was 305 with two bbl. . after i get a few miles one er again i'll be going i think the a cross ram setup . keeping in mind this is a hot rod type car for me . i don't want a sunday car or a grocery getter as that's whats the wife is for .
later on down the road i have a stroker kit for my poly 318 . if i live long enough and the lottery happens my way that to will get a chance in my 60 dart also .
the 413 deal may work for ya . but one thing you gotta remember is the 413 stuff is gettin real rare also . a 383 might be 20 ci. less but the same effects can be had with way less aggravation and the cross rams will still bolt .
it's goin to be a little bit before my engine change happens as right now i'm just putting together all the cosmetic parts i can , like aluminum v-covers , torker intake , all stainless bolt replacements , aluminum water pump - with aluminum case and a rebuilt 64 afb . . if not the afb then an edelbrock 600 or a holley 650 . the best thing for you to really keep in mind though is to build it for you and your purpose , remembering the smell of burning rubber in the morning . any questions you may have about your dart that i can help with i will and if i don't have the answers , i'll point you to who does -------------------------later




8
General BS and Laughs / vanishing threads
« on: October 31, 2008, 03:24:38 AM »
SINCE WHEN DO YOU BEND OVER TO THE CRITICS . PRADON ME BUT THAT IS JUST PLAIN OLD BULLCHIT WITH A CAPITAL------B. C. ! ! ! 60 dart2008-10-31 07:25:37

9
Tech- - Engine / What year 318 will fit?
« on: October 20, 2008, 12:21:58 AM »
mopar performance says yes they will interchange but with a slight difference they don't state . one alignment pin and one bolt hole doesn't match up . can't remember wich ones at this time but even so it's a direct bolt up early A and LA--------------------later 60 dart2008-10-20 05:23:34

10
Tech- - DRIVE TRAIN / driveshaft balancing
« on: September 28, 2008, 04:11:37 AM »
if a driveshaft is REinstalled and tested with a vibration , remove and reinstall turned 180* ----------------------later60 dart2008-09-28 09:12:26

11
por 15 doesn't like uv's but if you top coat while tacky with cheap chassis paint it works very well-----------------in time the top coat will wear but the 15 will be there for ever but may be touched up easily------still pretty good for an oooold fart----------------------------------------later 60 dart2008-08-13 10:50:46

13
Tech- - STEERING WHEELS AND SUSPENSION / PS Pump belt. Catch 22?
« on: July 28, 2008, 02:52:07 AM »
pull the belt ---hand turn the pulleys for any tightness or resistance and clean the pulley grooves with a mild abrasive like scotch brite(very clean) and last make very certain you have the right size belts (width)-------------------over sized or undersized belts and pulleys will slip and in time crystalize and screach------why ?---because they wear in quicker and loosen up------why clean pulleys ?---if they slip over long periods of time the pulley surface will heat and become extreamely smooth = slip-----------later

14
General BS and Laughs / Life is funny.
« on: July 18, 2008, 03:35:52 AM »
don't know bout the listenin part but i started negative postin on em 5 yrs. ago------got screwed on a dual stainless setup for my dart but hell i'm only out 860.00-------they went to the dumpster except the turbo mufflers------had a single set up made at classic exhaust at geneva on the lake ohio for 250 , they were off by three inches on pass side------i had to temp. weld back together my old single just to move the car------when i got time i built a jig for the single and made em good just as practice welding------they came out real good but i have no use for them-------my goal is to use a set of ballenger shorties i have--------------didn't mean to high jack the thread ---sorry guys----------------------------later

15
General Mopar Discussions / Guess what this is!
« on: July 18, 2008, 03:21:15 AM »
i'm not very high on the wheel choice but as a package , i like it very much , different , works for me------any underhood photos--------------------later

Pages: [1] 2 3
© 2008-2014 Steve Hobby • © 2015 Allpar, LLC