Please login or register.

Login with username, password and session length
Advanced search  


We changed servers, which is good, and lost all passwords, which is bad. See above.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - John B.

Pages: [1]
« on: May 27, 2011, 06:03:28 PM »
Bob; the top of my back passenger seat, in  my 66' Newport is heat cooked. No cracks or splits but "dried out" would be the best description. Any suggestions for preserving it? Thanks, John. 

General Tech- - BRAKES / Dodge Van
« on: May 27, 2011, 05:54:05 PM »
Hi Guys; Looking at a 73' Dodge Tradesman Van, with disc brakes. Will they fit the same as the 73' car assy's. Looking to add to the stash for future projects!  John.

General Tech- - BRAKES / Power Booster on 66' T&C
« on: August 05, 2010, 05:51:26 PM »
Hi guys; I'm knee deep in the middle of converting my Budd discs to 73 spindles rotors etc. I was lookin at an earlier thread where C-Barge talks about Boosters. Question, is the Midland- Ross booster used on the Budd system still available? My 66'T&C had Budds & cruise control, which makes for a tight fit. Secondly is that M-R booster a dual diaphragm? Most of the single diaphragm Boosters I can find are only rated for drum brakes. Oddly enough thats what was on the car (single diaphragm) when I bought it, and the owner said the brakes performed poorly. thanks, John.

General Mopar Discussions / retro a/c units
« on: May 20, 2009, 01:56:12 PM »
Hey guys; Has anybody covered removing the old style RV-2, A/C compressors and updating them to a lighter weight and size unit. John

General Mopar Discussions / new wheels
« on: May 07, 2009, 07:50:18 AM »
Hi fellas; I think this has been covered before but I want to upload some pic's of my new beast to the forum, can you help? not that pooter savvy! Thanks, John

Tech- - Engine / 440 to 413 swap
« on: May 04, 2009, 04:11:21 PM »
Hi fellas; I am pulling out a dead 440 from a 66 T&C Wagon. I have a  runner 65- 413, out of a New Yorker. Will these swap easily, other than engine mounts ? Thanks, John

Tech- - DRIVE TRAIN / driveshaft balancing
« on: September 27, 2008, 05:48:49 PM »
Hi fellas; I'm about to do the U-joints on my 69,300. the question is, should  the driveshaft be balanced? I seem to recall there is a certain way to install it to avoid vibration and such! am I on the right track here? thanks, John

General Tech- - BRAKES / Budd conversion
« on: August 13, 2008, 12:53:30 PM »
Hi Fellas; Has anybody tried using the later dual reservoir M. cyl & dual diaphram booster with a existing  Budd caliper & rotor set-up? The Budd parts are all but obselete now!
 I would appreciate the input, John

UPHOLSERY HOW TOO's / mold&mildew issues
« on: June 08, 2008, 01:21:28 PM »
Hi Guys; I'm wondering whats the best way to deal with mold &mildew in a car thats been stored in a Barn for years. Trying to save the interior, as its a 64 Imp Crown Coupe.
                                           thanks, John B.

Pages: [1]
© 2008-2014 Steve Hobby • © 2015 Allpar, LLC