MoparFins

Please login or register.

Login with username, password and session length
Advanced search  

News:

We changed servers, which is good, and lost all passwords, which is bad. See above.

Pages: 1 2 [3] 4 5 ... 7   Go Down

Author Topic: 9 1/4 rear: Running great!  (Read 2478 times)

Steve

  • Administrator
  • Hero Member
  • *****
  • Karma: +1/-0
  • Posts: 8653
    • View Profile
9 1/4 rear: Running great!
« Reply #30 on: December 01, 2009, 02:00:37 PM »

Yeah we know. . .there was a mass exidus from New York harbor when you were here for church.
 
Thank goodness for safety glass
Logged
Favorite Expression. . . Damned Kids.  Lots of projects.  Donations accepted

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #31 on: March 01, 2010, 09:14:44 AM »

I said screw it.  If Steve can do it, any numbskull can do it so that includes me despite my distribulexia.  I'm getting bored, haven't broken anything for a while, so I'm going in and swapping out the ring & pinion.
 
First things first.  I need to fabricate this tool (cuz I'm too cheap to buy it).  It looks like a socket on a pipe.  So whatizzit really?  How do I fab one of these things up?
 

 
 

Steve

  • Administrator
  • Hero Member
  • *****
  • Karma: +1/-0
  • Posts: 8653
    • View Profile
9 1/4 rear: Running great!
« Reply #32 on: March 01, 2010, 10:19:01 AM »

That is supposed to go down the tunnel and get to nuts on the end of the Carrier.  I don't know that you need it unless the instructions say so. . . .

My I suggest using several long 1/2 drive extensions? You will probably need 4 or 5. You can duct tape them to make them rigid at the joints.  You must have a harbor freight near by, or wal-mart.  You only need it once. . .   Then it's just a matter of finding out the hex size.



 
Simple enough?
Logged
Favorite Expression. . . Damned Kids.  Lots of projects.  Donations accepted

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #33 on: March 01, 2010, 11:08:49 AM »

Quote from: POLARACO
 I don't know that you need it unless the instructions say so. . . .
[color=#ffff00 size=2]Yes.  The instructions say so.  I'm going to follow the FSM on this.  [/color]
 
. . .   Then it's just a matter of finding out the hex size.
[color=#ffff00 size=3]...thus the reason of my post ??[/color]
 
Simple enough?

 
Commando12010-03-01 17:11:56

Snotty

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 3972
    • View Profile
9 1/4 rear: Running great!
« Reply #34 on: March 01, 2010, 01:08:02 PM »

Stan, Chris "the Doctor" Fredriksen could do that for you.  Unfortunately he's here in Bakerisfied.  :-(  My son has decided to pay Chris to turn our 3.55 8.75 third member into a sure-grip.  It's his money! 
 
Good luck doing that your self.  Be careful!
Logged
It's green here in Chico!!

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #35 on: March 01, 2010, 01:15:02 PM »

Quote from: Snotty
I have The Best and the Brightest covering my back.
 
3:15 A.M. :  Um...hello?  Steve?
Commando12010-03-01 18:16:59

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #36 on: March 02, 2010, 12:45:10 PM »

...and while we're at it, PICK MY KIT:
 
(the minimum kit nec.   "
 
http://ratech.stores.yahoo.net/ch9axinki.html

Steve

  • Administrator
  • Hero Member
  • *****
  • Karma: +1/-0
  • Posts: 8653
    • View Profile
9 1/4 rear: Running great!
« Reply #37 on: March 02, 2010, 01:41:37 PM »

Quote from: Commando1
Quote from: Snotty
I have The Best and the Brightest covering my back.
 
3:15 A.M. :  Um...hello?  Steve?


ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ



POLARACO2010-03-02 18:41:53
Logged
Favorite Expression. . . Damned Kids.  Lots of projects.  Donations accepted

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #38 on: March 03, 2010, 09:11:40 AM »

Oh, that's OK about the tool, guys.  The guys over at Moparts told me how to make one...

 

Steve

  • Administrator
  • Hero Member
  • *****
  • Karma: +1/-0
  • Posts: 8653
    • View Profile
9 1/4 rear: Running great!
« Reply #39 on: March 03, 2010, 01:13:52 PM »

sigh
 
I told you how to make one without all that on there.  Did you need the Hex? Or a socket?
Logged
Favorite Expression. . . Damned Kids.  Lots of projects.  Donations accepted

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #40 on: March 04, 2010, 03:40:20 AM »

Quote from: POLARACO
sigh
 
No you didn't.  I asked for SIZES.  I got silence from the peanut gallery.
It required me welding a 7/8" Heavy nut (1.41" hex head) welded to 3 ft of pipe with an old 1/2" drive socket welded to the other end.
 

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #41 on: March 12, 2010, 12:52:25 PM »

D(iferential Day) -3: Countdown to Going In.
 

Steve

  • Administrator
  • Hero Member
  • *****
  • Karma: +1/-0
  • Posts: 8653
    • View Profile
9 1/4 rear: Running great!
« Reply #42 on: March 12, 2010, 01:05:45 PM »

   
 
      
 
This won't be as messy when you blow it up
Logged
Favorite Expression. . . Damned Kids.  Lots of projects.  Donations accepted

Stan Paralikis

  • Hero Member
  • *****
  • Karma: +0/-0
  • Posts: 114897
    • View Profile
9 1/4 rear: Running great!
« Reply #43 on: March 12, 2010, 03:03:44 PM »

What's your problem, pops
At least my projects get finished.

Steve

  • Administrator
  • Hero Member
  • *****
  • Karma: +1/-0
  • Posts: 8653
    • View Profile
9 1/4 rear: Running great!
« Reply #44 on: March 12, 2010, 04:18:27 PM »

mine do too.  And I don't need to carry a shovel and broom either!
Logged
Favorite Expression. . . Damned Kids.  Lots of projects.  Donations accepted
Pages: 1 2 [3] 4 5 ... 7   Go Up
 

© 2008-2014 Steve Hobby • © 2015 Allpar, LLC